Source : http://www.cambase.io/vendors/axis/models/m3006-v
Thursday 1 December 2016
Reset Mikrotik
Jika reset Mikrotik lewat tombol reset gagal, bisa di coba dengan mengupgrade firmware mikrotik via netinstall dengan cara seperti dibawah ini
Success! My Mikrotik is back in working condition!! Thank you all
RB951G2HnD, Thank you so much for your guidance.
Dallen, You gave me the most important ingredient - hope... Mikrotik support just left me hanging with "Use NetInstall". But hearing your story made me try try and try till it worked...
Let me post what I did so that anyone else with the same problem may be able to fix it themselves.
a) Disable Firewall
b) Connect PC to Port 1 on Mikrotik
c) Disable all other network interfaces on the PC - LAN, Wireless, Virtualbox
d) Set static IP of 192.168.88.3 subnet mask 255.255.255.0 gateway 192.168.88.1 on PC
e) Run NetInstall
f) Select "Net Booting"
g) Mark "Boot Serve Enabled"
h) Selected Client IP address of 192.168.88.1
i) Keep reset pressed while powering on
j) Keep holding the reset pin till a beep sounds. Release immediately
k) Router showed up in Netinstall's list (**)
l) Unmarked "Keep old configuration" and "Configure Script"
m) Unzipped "all_packages-mipsbe-6.5.zip"
n) Selected all packages by browsing to the unzipped directory and using the "Select All" button
o) Clicked on "Install"
p) The progress bar moved to 100% as the packages were uploaded (**)
q) The router rebooted - Beep once, some time later (1 min or so if I recollect) a second beep
After a while after the second beep short (30 secs or so if I recollect) , the wireless light turned on, and the router configuration was as clean as the day I unpacked it (just 6 days ago!).
The nightmare was in steps (k) and (p) both marked with (**). The router would just not show up in NetInstall's list - must have tried it 30 times before this worked - But once I got it to work, it started working every time. And then after Clicking on "install" the router status would go to "Installing" and then to "Ready" without doing anything - no idea why the installation worked properly after 20 times of trying!
Irrespective, my router is back to being better than new - now upgraded to the later version of OS, and now with some additional packages!
Thanks you for your help and encouragement. Made all the difference for a beginner like me!
Now I need to get my production network running with dual-WAN and VPN...
Best regards,
Pradeep
Source : http://forum.mikrotik.com/viewtopic.php?t=77999
Success! My Mikrotik is back in working condition!! Thank you all
RB951G2HnD, Thank you so much for your guidance.
Dallen, You gave me the most important ingredient - hope... Mikrotik support just left me hanging with "Use NetInstall". But hearing your story made me try try and try till it worked...
Let me post what I did so that anyone else with the same problem may be able to fix it themselves.
a) Disable Firewall
b) Connect PC to Port 1 on Mikrotik
c) Disable all other network interfaces on the PC - LAN, Wireless, Virtualbox
d) Set static IP of 192.168.88.3 subnet mask 255.255.255.0 gateway 192.168.88.1 on PC
e) Run NetInstall
f) Select "Net Booting"
g) Mark "Boot Serve Enabled"
h) Selected Client IP address of 192.168.88.1
i) Keep reset pressed while powering on
j) Keep holding the reset pin till a beep sounds. Release immediately
k) Router showed up in Netinstall's list (**)
l) Unmarked "Keep old configuration" and "Configure Script"
m) Unzipped "all_packages-mipsbe-6.5.zip"
n) Selected all packages by browsing to the unzipped directory and using the "Select All" button
o) Clicked on "Install"
p) The progress bar moved to 100% as the packages were uploaded (**)
q) The router rebooted - Beep once, some time later (1 min or so if I recollect) a second beep
After a while after the second beep short (30 secs or so if I recollect) , the wireless light turned on, and the router configuration was as clean as the day I unpacked it (just 6 days ago!).
The nightmare was in steps (k) and (p) both marked with (**). The router would just not show up in NetInstall's list - must have tried it 30 times before this worked - But once I got it to work, it started working every time. And then after Clicking on "install" the router status would go to "Installing" and then to "Ready" without doing anything - no idea why the installation worked properly after 20 times of trying!
Irrespective, my router is back to being better than new - now upgraded to the later version of OS, and now with some additional packages!
Thanks you for your help and encouragement. Made all the difference for a beginner like me!
Now I need to get my production network running with dual-WAN and VPN...
Best regards,
Pradeep
Source : http://forum.mikrotik.com/viewtopic.php?t=77999
Subscribe to:
Posts (Atom)